James Hardie Fiber Cement Siding in Freeport, Maine

James Hardie fiber cement is a board of cement, sand and cellulose that will not rot, does not feed insects and is rated noncombustible, which suits a coastal town where salt air, fog and wet springs wear wood out. Hardie makes a product line engineered for cold, wet climates with repeated freeze-thaw cycles, and its factory-baked ColorPlus finish pushes the first repaint years down the road rather than a few seasons. On a bay-facing wall that takes spray every storm, that stability is the main argument.

Appearance is the other reason it fits here. Lap siding with a smooth face reads like painted clapboard on a Greek Revival house in Porter's Landing or an older farmhouse inland, and Hardie shingle panels echo the Shingle style of downtown's 1895 Congregational Church. The boards are heavy and must be held off roofs, decks and grade by specified gaps, so installation details matter more than with vinyl: flashing behind every butt joint, clearance where a wall meets a lower roof, and sealed cut ends. For a building downtown, where the Design Review Ordinance covers materials and facades, bring the plan to the town before materials are ordered.

Census estimates (ACS 2020-2024) put Freeport at roughly 4,250 housing units with a median year built of 1984, young for a town incorporated in 1789: about 17 percent of homes predate 1940 and about a quarter predate 1960; another 18 or 19 percent went up between 1960 and 1979, and roughly 30 percent were built in 2000 or later, leaving about a quarter from the 1980s and 1990s. Around 72 percent are single-family detached houses, close to 78 percent of occupied homes are owner-occupied, and some 280 units are held for seasonal use. The oldest stock is Federal and Greek Revival: the c. 1790 Mitchell-Soule-Davis cape and the c. 1830 brick Harrington House survive on Main Street, and saltbox farmhouses such as the Pettengill House and the Capt. Greenfield Pote House stand near Mast Landing and on Wolfe's Neck. Newer neighborhoods fill in between Route 1, I-295 and the river.

Freeport sits at the northeastern corner of Casco Bay, and the Harraseeket River carries the tide inland past South Freeport, Porter's Landing and Mast Landing. Houses on Wolfe's Neck, in South Freeport and along the river take salt air, fog and northeast wind off the bay in nor'easters, while homes west of I-295 sit in more sheltered, wooded country. Snow is a real load here: Portland International Jetport, the nearest long-record weather station, averages about 69 inches a season under the 1991-2020 normals, most of it from December through March. Winters swing above and below freezing again and again, so water that gets behind trim, into siding joints or under shingles freezes, expands and works deeper with each cycle. Ice dams form on poorly insulated older roofs.

Building permits come from the Codes Enforcement office at Freeport Town Hall, 30 Main Street. A permit is required for any structural work or change of use, alterations may need one too, and the town asks owners to check with the codes officer first; a complete residential application is usually approved within a week. The residential checklist asks deck applicants for pier locations, framing, fastening, guards, handrails and stairs, and asks for a window and door schedule with U-factors. Downtown renovations fall under the Design Review Ordinance and the Project Review Board, and land within 250 feet of tidal water or a coastal wetland is in the state shoreland zone.

Fiber cement is a mix of cement, sand and cellulose fiber pressed into planks, shingles and panels. It does not rot, insects do not eat it, it will not burn, and factory-applied finishes hold color far longer than site-painted wood. It is heavier and more exacting to install than vinyl, which is exactly why installation quality shows. The Back Cove home on this site was re-sided with a complete James Hardie package of wood-grain plank.

• Walls are stripped, repaired and wrapped, with flashing at every opening and roof-to-wall joint.
• Boards are cut with dust-controlled tools and fastened to the manufacturer's nailing schedule.
• Required clearances are held above roofs, decks and grade so the ends never sit in water or snow.
• Butt joints get flashing behind them, and cut ends are sealed or primed as the manufacturer specifies.
• Trim, caulk lines and touch-up are finished so the pre-finished color stays uniform.

• You want the look of painted clapboard without the paint cycle
• Wood siding keeps rotting at the bottom courses and around trim
• The house sits in wind and salt exposure that punishes other materials
• You want a non-combustible exterior

• Product line and profile: lap plank, shingle, panel or board-and-batten
• Pre-finished color versus site painting
• Trim package and detailing
• Tear-off, sheathing repair and house height
• Number of windows, doors and corners to flash and trim

Every job is priced from a free on-site visit. Typical ranges for the trade are on our siding page, and the details of this service are on the James Hardie fiber cement siding overview.

Back to the Freeport exterior services overview, or see every town on our Cumberland County service areas page.